Electronic Technician Resume

Desired Industry: Technician	SpiderID: 11532
Desired Job Location: Cincinnati, Ohio	Date Posted: 3/2/2007
Type of Position: Full-Time Permanent	Availability Date: Immediately
Desired Wage: 33000.00
	U.S. Work Authorization: Yes
Job Level: Experienced with over 2 years experience	Willing to Travel: Yes, Less Than 25%
Highest Degree Attained: Other	Willing to Relocate: Undecided

Objective:
Want a rather stable long term job which requires diverse skills and a lot of thinking and problem solving. I learn quickly and am willing to do so.

Experience:
09/2005 - 12/20/2006
RF Technician
Pole Zero, West Chester, OH
09/2005 - 12/19/2005 Temp thru Bartech Technical Services
12/19/2005 - 12/20/2007 Pole Zero Employee

Programmed, tested, and repaired (component level) high frequency RF filters, signal controllers/routers, power supplies, etc. for military applications.
Also did Environmental testing and assisted Engineering with production and/or product problems and testing new products. Once a month I was on weekend call for Environmental testing and troubleshooting.

03/07/05 - 07/15/05
Electronics Assembly Technician
Express Personnel, Assigned to Tyco Health Care., Cincinnati, OH

Download software and program, calibrate, fully test, and repair medical equipment. I am at present working in the injector unit in production. This unit manufactures Syringe I.V. Injectors mostly used in MRI rooms.

11/14/04 - 12/26/04
Engineering Technician
Belcan TechServices, Assigned to Xetron Corp., Cincinnati, OH

Assembled and tested antenna routing and filtering systems for transmit and receive to be used in KC135 aircraft. Used network analyzer with SP-View program to match coax cables and RF switches. Used Noise figure meters, spectrum analyzer, and signal generators to check noise figures. Did final check of all routing of all frequencies used.

8/13/96 - 6/8/04
Electronics Engineering Technician
Overhoff Technology, Inc.: Milford, OH

This is a small company that makes custom designed radiation detection equipment. Duties are primarily to modify and test the electronics of the equipment. I would take the schematic and component layout for a basic instrument and modify them to reflect the changes needed (open tracks, added jumpers and/or components, etc.). In most cases new circuits had to be designed and added. The board assemblers would then assemble the boards and would then test and fine-tune them, making changes as needed. The CAD operator would make the mechanical drawings for the machinist and cabinet assembler. Then all subassemblies would be put together and
I would do a final test and calibration of the equipment. Besides these duties we regularly designed new and unique equipment. Each of us has our own strengths but we all did every job, from CAD to prototyping, when called upon. Drew all schematics and PCB drawings for the latest SMD units. Also assisted in making Technical manuals and User Guides for equipment and equipment software use.

11/16/95 - 8/12/96
P.C. Specialist
Self Employed: Milford, Ohio

Setup and troubleshoot p.c. systems for individuals and businesses. Performed software and hardware setup and repairs. Found this not very profitable for the hours worked went back to work for another company.

5/17/90 - 11/16/95
Electronic Technician -- Test Engineering
Cincinnati Microwave, Inc.: Cincinnati, Ohio 45249

This company hired eight others and myself to form a Test Engineering Department to modernize the plant for sale in about five (5) years. The plant had 353 employees making two models of radar detectors at a rate of 300 per day and home arrest systems at a rate of about 20 per week. When sold it had 357 employees making; six models of radar detectors at a rate of 1500 per day for Cobra, Radio Shack, and Escort (Own Brand); 3 models of 900MHZ cordless phones at a rate of 650 per day for Cobra, Southwestern Bell, Southern Bell, AT&T, and Escort; and CDPD Modem Packets for various cell phone companies and cell phone users at a rate of 100 per day.

Built complete test systems. ---- Designed and built fixtures for electronic p.c. board testing to be mounted to mobile racks or automatic conveyor systems. Mounted instruments into cabinets or mobile racks and wired them into the fixtures and p.c. cards. Set up p.c. programs to operate fixtures and instruments to test p.c. boards to product specs. and pass data to the operator and a database on the network. This required some C++ program knowledge, p.c. hardware/software knowledge (Network use, data acquisition cards, etc.), some machine shop skills (Bridgeport Mill, band saw, grinder, etc.), detail work with hand tools, CAD design work, and electronic circuit design and testing. Worked with GPIB controlled instruments such as scopes, spectrum analyzers, signal generators, power supplies, meters, etc.

Maintenance -- Maintained systems across plant and performed modifications to systems and/or replaced them with new ones.

5/88 - 5/17/90
Electronic Technician - Field Service
Accounting Machine Corp.: Cincinnati, Ohio

Performed preventative maintenance, modifications, accessory setups, repairs, programming etc. on all types of electronic equipment such as, copiers, computers, cash registers, calculators, dictating machines, etc.

These services were performed on location. My area was from Richmond, IN - Milan, IN - Louisville, KY as a western border to West Union, OH - Portsmouth, OH - Lexington, KY as an eastern border. I left this company for a much better paying job.

6/84 - 5/88
Electronic Technician - Service Department
SCOT Business Machines Corp.: Cincinnati, Ohio

Performed preventative maintenance, modifications, accessory setups, repairs, programming etc. on all types of electronic equipment such as, copiers, computers, cash registers, calculators, dictating machines, etc.

Also performed mechanical and electrical repairs on IBM electric typewriters.

6/78 - 6/84
Electronic Technician - Service Department
Harris Corp.: Cincinnati, Ohio

Performed preventative maintenance, modifications, accessory setups, repairs, programming, calibration etc. on electronic equipment such as, digital control modules for vacuum plating systems, frequency counters, oscilloscopes, multimeters, etc.

Also performed mechanical and electrical repairs on motor and hydraulic systems and plumbing repairs on chemical wash stations.

6/74 - 6/78
Electronic Technician (MOS 2819) - United States Marine Corp.
TOP SECRET Security Clearance - Finished E5 (Sergeant)

Performed set-up, preventative maintenance, and component level repairs on teletypes, card readers, tape readers, AM SSB transceivers, FM transceivers, Microwave (Satellite) Transceivers, cryptographic equipment, and computers and all associated computer interfaces. Performed these tasks on small portable field units as well as rack-mounted units in communication modules.

Education:
8/74
Air Force Cryptographic School: Lackland AFB, San Antonio, TX
Trained in the repair, setup and operation of TOP SECRET encryption equipment. Trained to the component level.

7/74
Naval Digital Communications School: Norfolk NB, Norfolk, VA
Advanced training in digital comm. equipment repair, setup and operation. Trained to the component level for phone and satellite transmission equipment as well.

6/74
Marine Corp. Electronics Training School: 29 Palms MCB, 29 Palms, CA Completed Basic Electronics Courses started in college.

Skills:
Taught object oriented programming in C++ p.c. language and basic Visual Basic programming. Now self- teaching C++ in depth and Visual Basic advanced (DLL's etc.). Have learned, through work experiences and self teaching, PIC programming, Electronic CAD use, PSpice use, Bridgeport Mill use, other machine shop equipment and hand tools used for modeling, advanced photo, art, and desk top publishing software use, and advanced art techniques in ALL mediums for commercial and private use. Have examples of artwork and programming available upon request. Also have sample User's Guide available.

Reference:
Richard Kyrlach
545 U.S. Highway 62
Winchester, Ohio 45697
Home:(937) 442-3804

Joel Baker
1523 Red Oak Drive
Loveland, Ohio 45140
Home: (513) 722-1366

Janna Gregory
477 Gay Street
Williamsburg, Ohio
Home: (513) 724-7708

Candidate Contact Information:

Name: Clarence Mallinson
Street:	Phone: 513 722-0247
City: Milford	Fax: -
State: Ohio
Zip: 45150
Web Site: